A haul truck can carry hundreds of tons down a ramp, so a missing check can become an incident before anyone reaches the pit floor. Most serious defects are visible at the start of the shift: a seeping cylinder, a bulging sidewall, a brake that grabs. This checklist covers eight zones in walk order. Start free and run every pre-start digitally.

Brakes · Tires · Steering · Hydraulics · Safety systems

Mining Haul Truck Inspection Checklist: Safety & Roadworthiness

Our Truck Inspection & Maintenance Management Software turns this checklist into a digital pre-start: operators tick each zone on a phone or tablet, photograph defects, and every finding becomes a logged work order tied to that truck.
$5K–$20Kestimated cost per hour of one haul truck down
~30 mintypical full pre-shift check on an ultra-class truck
§56.14100US surface-mine rule: the operator inspects before the shift

The Rule Behind the Routine: What US Mine Rules Expect Before a Truck Moves

At US surface metal and nonmetal mines, 30 CFR 56.14100 sets a simple chain: inspect, fix, tag out, log. Following it turns a daily habit into a record.

aOperator inspectsBefore the equipment is placed in operation for the shift.
bSafety defects fixedPromptly, before they turn into a hazard to people.
cHazard? Tag it outThe truck is taken out of service and tagged or parked in a designated area.
dNot fixed yet? Log itReport it and keep the log at the mine until the defect is corrected.
Brake rule, 30 CFR 56.14101
Service brakesMust stop and hold the truck with its typical load on the steepest grade it travels.
Parking brakesWhere fitted, must hold the loaded truck on that same grade.
Working orderEvery installed braking system must be kept in working order.
Outside the US, or at coal sites, follow your own jurisdiction's rules and the manufacturer's procedures. This checklist supports them, not replaces them.

Go, Watch or Tag Out: How to Rule on Every Finding

Every unticked box needs a decision. Three outcomes cover almost everything, and the operator should never have to guess which one applies.

GoPasses the checkTick the box and continue. Nothing to record beyond the completed pre-start.
WatchDefect, no immediate hazardLog it with a photo and raise a work order. Typical examples: a minor weep, a worn belt, a dim work light.
Tag outHazard if the truck keeps workingDon't move the truck. Tag it out, report it, and release it only after repair. Items marked Tag-out item below usually land here.
Example: some sites tag out a tire when TPMS temperature passes a set limit; one cited example is above 185°F. Use the limit in your OEM manual and site procedure.

The Pre-Start Checklist: Eight Zones in Walk Order

Work the zones in order so nothing is skipped. 38 checks in all, with the highest-risk items flagged.

1Walk-Around5 checksAbout 5 min
2Tires & Wheels5 checksTPMS first
3Brakes & Steering6 checks§56.14101
4Engine & Fluids5 checksLevels and leaks
5Hydraulics4 checksHoist and steering
6Cab & Controls5 checksROPS and cameras
7Lights & Warnings4 checksBe seen and heard
8Fire Suppression & Safety4 checksBefore you leave the ramp

A full pass takes about half an hour on the largest trucks, with the walk-around alone near five minutes. A check that finishes in well under that is usually a check with skipped steps. Contact our team to adapt this checklist to your fleet and site rules.

How Truck Inspection & Maintenance Management Software Runs the Pre-Start

Paper pre-starts get lost, and a defect scribbled on a clipboard rarely reaches the shop in time. Our software keeps the whole chain in one record, from the first tick to the closed repair.

Example pre-start record (illustrative)
TruckHT-204, shift start 05:47
Checks38 of 38 completed
Findings1 Watch: hoist cylinder weep, photo attached
Tag-out items0 — truck cleared to operate
Work orderOpened automatically and linked to the truck's history
Checklists on a phone or tabletOperators work the eight zones in order and attach a photo to any defect.
Findings become work ordersA defect reaches the shop with the truck, the zone and the photo, so nothing waits on a clipboard.
A defect log that is always retrievableOpen defects stay on record against each truck until they are corrected, ready for any review.
History across the whole fleetSee which trucks keep failing the same check and tighten their maintenance before the next shift.

Every Pre-Start Complete, Every Defect Logged

Truck Inspection & Maintenance Management Software gives operators a guided digital checklist, gives the shop a work order for every finding, and gives you a defect log you can pull up in seconds. Fewer surprises on the haul road, fewer hours lost to preventable failures.

Frequently Asked Questions

What should a mining haul truck inspection checklist include?
At minimum: a walk-around, tires and wheels, brakes and steering, engine and fluids, hoist and steering hydraulics, cab and controls, lights and warnings, and fire suppression and safety systems. Mark the items that must stop the truck if they fail, such as brakes, steering, sidewall damage and the fire suppression system. Start free and turn this list into a digital pre-start.
Who has to perform the pre-shift inspection?
At US surface metal and nonmetal mines, 30 CFR 56.14100 puts the pre-operation inspection on the equipment operator, before the equipment is placed in operation for the shift. Other jurisdictions and sites have their own rules, so check yours.
What happens when a defect is found?
Safety defects should be corrected promptly. If a defect makes continued operation hazardous, the truck is taken out of service and tagged or parked in a designated area until it is repaired. A safety defect that can't be fixed immediately is reported and logged, and the log is kept at the mine until the defect is corrected. Book a demo to see how defects are logged and tracked.
How long should a haul truck pre-shift inspection take?
Guidance for the largest ultra-class trucks puts a full check at around 30 minutes, with the walk-around near five. Smaller trucks take less time. If a full check is regularly finishing in a few minutes, steps are probably being skipped.
Inspected · Logged · Ready to haul

Stop Starting Shifts on Trust Alone

Truck Inspection & Maintenance Management Software keeps every haul truck pre-start complete, every defect logged and every repair tied to the truck it belongs to.

No credit card required. Free for up to 3 trucks. Built for FMCSA-compliant fleets.