A fleet manager copies one PM schedule onto every International LT in the yard. Six months later, one truck is changing oil far too soon, another is running a heavy idle cycle on an interval that was never meant for it, and nobody can say which engine is which. The fix starts with knowing the engine, the duty cycle and the date of every service. This guide walks through the International LT maintenance schedule for Cummins X15 trucks: oil and filters, coolant, aftertreatment, and the checks that belong on every PM. Start free and set PM intervals truck by truck.
Inspect · Find Defects · Work Orders · PM by Truck
International LT Maintenance Schedule: Cummins X15 Service Guide
One copied PM schedule is wrong for some of your trucks. Truck Inspection & Maintenance Management Software lets you set X15 service intervals for each International LT by miles, hours or date, turns inspection findings into work orders, and keeps every oil change, filter and aftertreatment check on the truck's record.
No credit card required. Free for up to 3 trucks.
1InspectPre-trip and DVIR catch leaks, lamps and low fluids.
2Defect to work orderEach finding becomes a tracked repair job.
3Service recordedFilters, fluids, labor and photos stay on the truck.
4Next PM setDue by miles, hours or date, per truck.
Step 1: Know Which Engine You're Servicing
The International LT can be ordered with different engines, so there is no single LT schedule. This guide covers trucks with the Cummins X15. The service ladder also changes with model year and emissions generation.
This guideCummins X15Intervals are keyed to duty cycle, measured by fuel economy, plus idle and PTO time.
Check separatelyOther LT enginesUse that engine maker's manual. Do not apply X15 numbers to a different engine.
Step 2: Find Your Duty-Cycle Band
Cummins sets X15 oil drain intervals by fuel economy, because a hard-working truck loads its oil faster. Here is the published range from the X15 Productivity Series.
X15 oil drain interval by duty cycle (miles)
⚠️
Watch idle and PTO timeCummins says that if idle plus PTO time exceeds 40% for short-haul, normal or light duty, use the next lower drain interval. Oil analysis can be useful, but Cummins states it does not justify extending the drain interval. Intervals differ by model year, so always confirm with your Operation and Maintenance Manual or a Cummins dealer.
Step 3: The X15 Service Ladder
Think of service as four rungs. Each has its own rhythm, and your system should track all of them.
1
Every day: dash and fluidsCheck oil pressure, coolant temperature, DEF level and warning lights before rolling.
2
Every oil change: oil, filter, inspectionChange oil and filter together, check the air filter and look over belts, hoses and leaks. Fuel filters follow the manual.
3
About every 6 months: coolant testCummins guidance calls for regular coolant testing, with drain and refill per your coolant supplier.
4
Long intervals: aftertreatment and engineDEF filter at about 300,000 miles or 6,750 hours, DPF cleaning by duty cycle, and valvetrain work per the manual.
Aftertreatment: Three Systems to Watch
Emissions parts are where small ignored warnings become big repair bills. Track each one.
DPFCleaning intervals in Cummins data range from 250,000 to 800,000 miles depending on duty cycle and generation. Watch for regen and warning lights.
SCR and DEFKeep DEF clean and topped up, tighten the cap and replace the DEF filter on schedule.
EGR and sensorsCheck for leaks and fault codes at each PM, and log any recurring dash lamp as a defect.
PM Checklists You Can Copy
PM A: every oil change
- Engine oil and filter
- Fuel filter, per manual
- Air filter inspection
- Belts, hoses and visible leaks
- Aftertreatment visual check
- Transmission and axle leak check
PM B: roughly every 6 months
- Coolant test and top-off
- DEF system and cap check
- Charge air and exhaust connections
- Transmission fluid per its manufacturer
- Review open defects and fault codes
- Update service dates and photos
One Schedule per Truck, Not per Fleet
Truck Inspection & Maintenance Management Software lets each LT carry its own PM intervals and records every service against the truck. Start with up to 3 trucks free.
How the Software Keeps the Schedule Honest
PM by truckSet miles, hours or date triggers for each International LT.
Defects to work ordersA leak or dash lamp noted on inspection becomes a tracked job.
Full service historyOil, filters, DEF and coolant work stay on the truck's record.
Photos and laborAttach proof and time to every PM so records hold up.
Frequently Asked Questions
How often should a Cummins X15 oil change be done?
It depends on duty cycle. Published X15 Productivity Series intervals run from 25,000 miles for severe duty to 75,000 miles for light duty, and heavy idle time shortens them. Confirm against your manual.
Start free and set the right interval per truck.
Does one maintenance schedule fit every International LT?
No. Engine type, model year and duty cycle all change the intervals, so set them per truck.
When is the DEF filter replaced?
Cummins data lists about 300,000 miles or 6,750 hours for the X15 DEF filter. Check your engine's manual for the exact figure.
How does software help with PM scheduling?
Inspect · Repair · Record · Schedule
Put Every International LT on the Right Schedule
Set X15 PM intervals by truck, log defects as they appear and keep service records ready when you need them.
No credit card required. Free for up to 3 trucks.