A small clunk when the driver shifts out of reverse is the driveline asking for attention. Left alone, a dry U-joint seizes, the shaft whips, and a repair that cost a few hundred dollars in the shop becomes a tow and a lost day. This checklist shows what to look at, what each symptom means and what to log. Start free and put every driveline check on a schedule.
U-joints · Slip yokes · Center bearings · Driveshafts
Truck Driveshaft and U-Joint Inspection Checklist: Wear & Failure Signs
Our Truck Inspection & Maintenance Management Software turns this checklist into a digital driveline inspection: technicians tick each point, photograph play or leaking grease, and every finding becomes a work order on that truck's record, so a repeat clunk never goes unnoticed.
$320 vs $3,200estimated cost of one U-joint in the shop vs at the roadside
4 of 4bearing cups should purge fresh grease
Shake firstgrease can hide play, so test before you lubricate
The Driveline Chain: Seven Links, Three Where Failures Usually Start
Power flows in one direction, and every link depends on the one before it. A worn slip yoke, a dry U-joint or a tired center bearing sends vibration through the rest of the shaft.
Transmission
Slip yoke
U-joint
Driveshaft
Center bearing
U-joint
Drive axle
Highlighted links are the usual wear points: the slip yoke, the U-joints and the center support bearing.
Symptom Decoder: What the Truck Is Telling You
Most driveline failures announce themselves first. Match what the driver reports to the likely source, then run the first check.
SymptomLikely sourceFirst check
Clunk shifting between drive and reverseWorn U-joint bearings or slip yoke splinesShake test, then check slip yoke grease
Squeak at low speed, under about 10 mphDry U-joint with metal-on-metal contact startingPurge all four cups and read the grease
Vibration at highway speedOut-of-balance shaft, worn joint, bent tubeLook for missing weights, check runout
Vibration felt in the cabWorn or hardened center support bearingInspect the rubber and turn the bearing by hand
Black, burnt or gray-metallic grease at purgeOverheated or contaminated joint, failing sealReplace the joint, then find the cause
Guidance combines OEM-aligned maintenance articles and vendor guides. Always confirm limits and intervals in your driveline manufacturer's service documents.
The Driveline Inspection Checklist: Follow the Torque, 28 Checks
Start at the transmission and work back to the axle. Each group shows how that part usually fails, so a symptom points straight to a group.
Water in the grease means the seal has failed and the joint should be replaced, not just regreased. Greasing without a shake test first can hide play, because new grease temporarily fills worn areas. Contact our team to build this into your PM checklist.
The Numbers Worth Knowing
6°commonly cited maximum working angle at a U-joint
1°commonly cited maximum angle difference between front and rear joints
4cups to purge fresh grease on a standard U-joint
15K–50K mitypical grease-interval range, depending on joint type and duty
Angle figures come from a 2008 maintenance guide, and intervals vary by manufacturer. Treat them as starting points, not specifications.
Fix it early or fix it on the road (vendor-published estimates)
U-joint$320 in shop
$3,200 at the roadside
Driveshaft$400–$1,200
$5,000+ after separation
How Truck Inspection & Maintenance Management Software Keeps the Driveline on Record
A clunk reported once is a note. A clunk reported three times on the same truck is a pattern. Our software keeps every finding, lube date and repair on each truck's record, so patterns show up before the shaft does.
Driveline history, Truck 62 (illustrative)
MarClunk reported on the pre-trip. Shake test finds play in the rear U-joint; joint replaced and work order closed.
JunScheduled PM. All four cups purge fresh grease; slip yoke lubed; reminder set for next interval.
SepCab vibration reported. Center bearing rubber found cracked and replaced before it let the shaft sag.
Lube and inspection triggersServices come due by mileage, engine hours or date, whichever fires first, and drivers are reminded in time.
Symptoms become work ordersA reported clunk or vibration reaches the shop with the truck, the symptom and a photo.
Repeat problems stand outThe same complaint on the same truck is easy to spot in its history.
Records ready for auditsEvery inspection and repair stays on the truck's record for DOT reviews.
Catch Driveline Wear While It Is Still a Small Job
Truck Inspection & Maintenance Management Software gives technicians a guided digital driveline checklist, turns every finding into a work order and keeps each truck's lube and repair history in one place. Fewer roadside separations, fewer emergency bills.
Frequently Asked Questions
How often should truck U-joints be inspected and greased?
It depends on the joint type, the manufacturer and the duty cycle. Guidance for greasable joints ranges from around 15,000 miles in severe duty to 40,000–50,000 miles on-highway, and more often off-road or in city work. Always shake-test before greasing and purge every cup until fresh grease shows.
Start free and set lube reminders by mileage or hours.
What are the signs of a bad U-joint?
A clunk when shifting between drive and reverse, a squeak at low speed, vibration at speed, and play when you shake the shaft. At service, black, burnt-smelling, gray-metallic or watery grease points to a failing joint, and a cup that won't purge is a reason to replace it.
Why does driveshaft vibration show up above a certain speed?
Rotating parts that are slightly out of balance vibrate more as speed rises. Missing balance weights, worn joints, a bent tube or a tired center bearing are the usual causes, and fleet guides suggest a balance check when drivers report vibration above roughly 45 mph.
Contact us to see how vibration reports are tracked per truck.
Are permanently lubricated U-joints maintenance-free?
No. They save you the greasing, but they still need inspection at the appropriate intervals. Check for play, damaged seals and loose hardware the same way you would on a greasable joint.
Inspected · Lubed · On record
Stop Waiting for the Shaft to Tell You
Truck Inspection & Maintenance Management Software keeps every driveline check complete, every symptom tracked to a repair and every lube date in view.
No credit card required. Free for up to 3 trucks. Built for FMCSA-compliant fleets.